DATACOM / Business Networking / Indoor AP / Bridge - EWS310AP


Name:
Model:


  • Supports IEEE 802.11a/b/g/n standards with up to 300 Mbps on each band
  • Up to 29 dBm high RF power on 2.4 GHz. Up to 26 dBM on 5 GHz for enhanced wireless coverage
  • Dynamic Channel Optimization
  • Designed for ceiling or desktop deployments
  • 4 internal MIMO antennas/Dual band
  • Band Steering shifts Dual band clients to 5 GHz for better throughput performance
  • Fast Roaming when used with a RADIUS server

DESCRIPTION


The EWS310AP can operate as a stand-alone Access Point connecting to third-party PoE-capable switches but more control and versatile management of the Access Point is achievable when it is part of an EnGenius Neutron Series wireless network management solution because the AP includes firmware that enables it to be immediately discovered, configured, monitored and managed from a compatible Neutron Series PoE+ Switch (EWS5912FP, EWS7928FP or EWS7952FP).

This capability enables IT managers to deploy and manage up to 50 EWS310APs from Neutron Series Switch allowing for simplified management from one browser-based interface including simultaneous firmware upgrades, clustering, traffic monitoring, bandwidth steering and many other features that can be reset or reconfigured from the convenience of the IT manager’s desktop.

Operating in both the 2.4 GHz and 5 GHz frequency spectrums and supporting 802.11a/b/g/n standards the EWS310P features wireless speeds up to 300 Mbps on each radio, a Gigabit port for connecting to 802.3at/af-capable PoE Switches, and an enhanced receive sensitivity MIMO (Multiple In / Multiple Out) antenna array. As a result, the EWS310AP is ideal for spacious environments such as large homes, small and medium-sized businesses, multiple-floor offices, hotels, hospitals, and other multi-floor buildings. 

As the EWS310AP is designed for deployments on ceilings where power outlets may be scarce, it also comes equipped with PoE (Power-over-Ethernet) IEEE 802.3at/af for use with an 802.3at/af-capable PoE injector or 802.3at/af-capable PoE Switches, drawing up to 15.6 watts of power.

To protect sensitive data during wireless transmissions, the EWS310AP offers different industry-standard encryption settings for wireless transmissions, including WEP, WPA-PSK, WPA2-PSK, WPA-PSK Mixed, WPA Enterprise, WPA2 Enterprise, and WPA2 Mixed Enterprise. It also includes MAC address filtering to allow network administrators to offer network access only to verified computers and devices based on their MAC addresses.

 

FEATURES


NEUTRON SERIES MANAGED ACCESS POINT
Can be configured, managed and monitored with several Neutron Series Access Points from the browser-based interface of one Neutron Series Wireless Management PoE+ Switch. After a Neutron Series Layer PoE+ Switch discovers the EWS310AP it can be "added" and set to be "managed" by the Switch. The Neutron Wireless Management solution supports bulk firmware upgrades and other features that can be set and managed across deployed Neutron Series Access Points simultaneously.

WIRELESS SPEEDS
Up to 300 Mbps on each of the 2.4 and 5 GHz frequency bands for faster file transfers and smoother video streaming.
Dual-Band for Expanded User Capacity
802.11n concurrent Dual-band operation in the 2.4 GHz and 5 GHz. Can support up to 100+ users (1)

HIGH POWER, LONG-RANGE, MULTIPLE FLOOR PENETRATION
Up to 29 dBm on the 2.4 GHz band and up to 26 dBm on the 5 GHz band provides more than twice the wireless coverage over mainstream competitors and enables the wireless signal to penetrate floors, ceilings, and walls for greater device connectivity. Internal MIMO antenna array provides better reception and performance as clients change their orientation.

SSID-to-VLAN Tagging
Can be configured to broadcast up to 16 SSIDs (8 SSIDs per frequency band). Each SSID can be tagged to a specified network VLAN for different user access tiers based on established access rights. 

User capacity performance results may vary based on topology configuration, structural and architectural elements, environmental factors, type of data traffic, RF capabilities of client devices, distance, RF interference in the operating environment and other factors.

Specifications


Technical Specifications

Hardware
RF: 2.4 and 5 GHz Frequency Bands
Standard: IEEE 802.11a/b/g/n
Radio I: 11b/g/n: 2.412~2.484 GHz
Radio II: 11a/n: 5.18-5.24 and 5.26-5.32 and 5.5-5.7 and 5.745-5.825 GHz
Data Rate: Up to 300 Mbps in both frequency bands
Memory: 64MB
Flash Memory: 16MB
Power Consumption: Up to 16W

Antenna
Four (4) Internal 5 dBi Omni-Directional AntennasRF: 2.4 and 5 GHz Frequency Bands

Physical Interface
1 x RJ-45 Gigabit Ethernet (10/100/1000 Mbps) - PoE capable
1 x Reset Button
1 x Power Connector

Power Requirements 
Power Supply: 100 to 240 VDC ± 10%, 50/60 Hz
(depends on different countries)
Active Ethernet (Power-over-Ethernet, IEEE 802.3at/af)
Power Adapter (United States) 48VDC/0.375A
Device: 12V/2A

Modulations 
OFDM: BPSK, QPSK, 26-OAM, 64-QAM, DBPSK, DQPSK, CCK

Operating Channels
2.4 GHz: US/Canada 1-11
5 GHz: Country dependent for the following ranges:
36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140, 149, 153, 157, 161, 165


Software

Operation Modes 
Access Point, Mesh AP (available soon)


Multiple BSSID 
Supports up to 8 BSSIDs per radio


LAN
IP (check validity and DHCP server IP range) MAC

SSID-to-VLAN Tagging
Supports 802.1q SSID-to-VLAN tagging

Spanning Tree
Supports 802.1d Spanning Tree Protocol

Wireless 
Wireless Mode: 11a/11b/11g/11n
Channel selection (settings vary by country)
Channel bandwidth (Auto, 20 MHz, 40 MHz)


Transmission Rate 
2.4 GHz: 11n only, 11b/b/n mix, 11b only, 11b/g, 11g only
5 GHz: 11n only, 11a/n mix, 11a only

QoS
WMM  (Wireless Multimedia)

Wireless Management Features (with Neutron Series Switch)
• Access Point Auto Discovery and Provisioning 
• Access Point Auto IP Assignment 
• Access Point Cluster Management 
• Remote Access Point Rebooting 
• Access Point Device Name Editing 
• Access Point Radio Settings
• Band Steering 
• Traffic Shaping
• Fast Handover 
• Seamless Roaming (requires RADIUS server)
• Access Point Client Limiting 
• Mesh Network* 
• Wireless Security (WEP, WPA/WPA2 Enterprise, WPA/WPA2 PSK) 
• VLANs for Access Point- Multiple SSIDs 
• Guest Network 
• Access Point Status Monitoring 
• Wireless Client Monitoring 
• Wireless Traffic & Usage Statistics 
• Visual Topology View 
• Floor Plan View 
• Map View 
• Secure Control Messaging 
• SSL Certificate 
• Local MAC Address Database 
• Remote MAC Address Database (RADIUS) 
• Unified Configuration Import / Export 
• Bulk Firmware Upgrade Capability 
• Intelligent Diagnostics

* Mesh networking mode available soon as a free firmware upgrade

Management

Tx Power Control:
Adjust transmit power by dBm

Configuration:
Web-based configuration (http)

Firmware Upgrade: 
Via web browser, settings are reserved after upgrade

Administrator Setting: 
Administrator Username and Password Change

Reset Setting: 
Reboot (press and hold for 2 seconds).
Reset to factory default (press and hold for 10 seconds)

System Monitoring: 
Status Statistic and Event Log

SNMP: 
V1, V2c, V3

MIB: 
MIB I, MIB II (RFC1213) and private MIB

Traffic Shaping: 
Incoming and outgoing wireless traffic shaping

Auto-channel Selection: 
Automatically selecting least congested channel

Bandwidth Measurement: 
IP range and bandwidth management

Auto Reboot: 
Reboot Access Point by minute, hour, day, or week

Backup and Restore: 
Save and restore settings through Web interface

CLI: 
Supports Command Line Interface

Diagnosis: 
IP pinging statistics

Log: 
SysLog and Local Log support

LED Control: 
On/Off

AP Detection: 
Scanning for available EnGenius APs

Wireless Security
WPA/WPA2 Personal (WPA-PSK using TKIP or AES)
WPA/WPA2 Enterprise (WPA-EAP using TKIP)
802.1X RADIUS Authenticator: MD5/TLS/TTLS, PEAP
SSID broadcast enable/disable
MAC Address Filtering, Up to 50 field
L2 Isolation (Access Point mode)

QoS (Quality of Service) 
WMM (Wireless Multimedia)

Environmental & Physical

Temperature Range 
Operating: 0 to 50ºC (32º to 122ºF)
Operating humidity: 0 to 90º
Storage temperature: -20ºC to 60ºC (-4Fº to 140ºF)

Humidity (non-condensing)
Operating: 90% or less
Storage: 90% or less

Certifications 
FCC, IC

Maximum data rates are based on IEEE 802.11 standards. Actual throughput and range may vary depending on many factors including environmental conditions, distance between devices, radio interference in the operating environment, and mix of devices in the network. Features and specifications subject to change without notice. Trademarks and registered trademarks are the property of their respective owners. For United States of America: Copyright ©2014 EnGenius Technologies, Inc. All rights reserved.

Dimensions & Weights
EWS310AP Device 
Weight: 0.80 lbs.
Length: 6.36”
Width:  6.36”
Height: 1.64”

Package Contents
EWS310AP Dual Band N600 Indoor Access Point
12V/2A Power Adapter
T-Rail Mounting Kit
Ceiling Mount and Wall Screw Kit
Mounting Bracket
RJ-45 Ethernet Cable
Quick Installation Guide

Warranty 
1 Year

EWS310AP - Document and Datasheets Download

 
datasheet_EWS310AP_Dec13_updatedFormat_revF.pdf
 
EWS_Indoor_AP_UM-082014.pdf
 
EWS310AP.zip
 
EWS_Indoor_AP_UM-082014.pdf
Copyright © 2013 EnGenius. All rights reserved.